Extremly clean chases
MACROZA Diamant D2 wall chaser has been specially designed and manufactured for opening chases on extremely hard materials such as concrete and all sorts of stone.
It is the recommended wall chasing machine for small jobs at residential houses or interior renovations at inhabited places where extremely clean chases are needed. This will be achieved by using a vacuum system to collect all dust.
Diamond blades used by MACROZA D2 are top quality laser-welded, especially designed for MACROZA.



Technical Specifications
Electricity | Motor | Single Phase | |
Class II | ![]() |
||
Voltage | 230 V AC ~ | ||
Frecuency | 50 Hz | ||
Power at full load | 2.000 W. | ||
Maximum consumption | 9 Amp. | ||
Cutting depth | 125 x 22,2 mm Disk | 15 / 32 mm. | |
240 x 22,2 mm Disk | 0 / 45 mm. | ||
180 x 22,2 mm Disk | 0 / 54 mm. | ||
Cutting width | 125 x 22,2 mm Disk | 5 / 47 mm. | |
240 x 22,2 mm Disk | 5 / 47 mm. | ||
180 x 22,2 mm Disk | 5 / 47 mm. | ||
Thecnical data | Weight | 7,7 kg | |
Acustic power level | 115 dBA (+/- 3 dB) | ||
Vibration level | 5 m/sg2 | ||
![]() |
![]() ![]() ![]() ![]() |
MDE1 Dust Collector
HIGH CAPACITY DUST COLLECTION DEVICE WITH ELECTRIC TELEHANDLE SYSTEM
MACROZA double diamond blade wall chaser Diamant D2 is directly connected to a Dust Collection device. By switching on the wall chaser, the dust collector will be switched on as well.
After switching off the wall chaser, the vacuum system MDE1 will remain running for another 10 seconds to empty the vacuum tube of dust and debris.
Technical Specifications
Motor | Single Phase | ||
Class II | ![]() |
||
Voltage | 110/230 V AC ~ | ||
Frecuency | 50/60 Hz | ||
Absortion power | 1.200 W | ||
Storage capacity | 20 L | ||
Maximum flow | 170 m3/h | ||
Weight | 10 Kg | ||
Hose length | 4 m. |
Maintenance
KEEPING YOUR WALL CHASER WELL SERVICED WILL EXTEND THE LIFE OF YOUR EQUIPMENT
We strongly recommend that all maintenance of Macroza Wall Chasers is done at an official Macroza Technical Service Centre.
Regular maintenance should be done to ensure best performance of your wall chaser.
Very Important! Make sure cuts are done straight on the material. Do not work with the machine twisted; otherwise discs will bend and/or break leading to machine’s failure.
State of the discs
Check whether discs are saturated after the slightest cutting failure. If this is the case, stop working with the DIAMANT D2 and proceed to clean the discs.
To clean the discs it is sufficient to cut some brick or limestone. Afterwards, continue working normally.
Wall Chaser cleaning
After each day of use, clean thoroughly the wall chaser so that there are no dust remains. If necessary, blow shots of compressed air through the machine’s ventilation slots to remove all remaining dust.
All MACROZA Wall Chasers used on daily basis should be checked on monthly basis.
Discs wearing
It is extremely important to check if there is any play in the bearings. At the slightest play we strongly recommend the bearings are changed. Failure to do so may lead to severe failures in the machine engine. In normal working conditions and due to the harsh nature of the chasing job, it may be necessary to change the bearings once a month.
Carbon brushes
Look through the chaser’s lateral ventilation slots to check whether there are sparks produced by the carbon brushes in the coil. If necessary replace carbon brushes. Always replace both carbon brushes.
For other wall chaser’s spare parts there are no maintenance period defined. They will be replaced as necessary.
For other wall chaser’s spare parts there are no maintenance period defined.
They will be replaced as necessary.